|
|
|
|
The table below lists the "go to" and "push to" telescope models that are supported by TheSkyX Serious Astronomer Edition.
For step-by-step setup instructions on how to setup and control your telescope, see TheSkyX Professional and Serious Astronomer Edition User Guide (PDF). |
|
Manufacturer |
Series |
Model Number |
|
GTO series mounts |
All models*, including:
*TheSkyX Serious Astronomer Edition's native Astro-Physics mount driver states that firmware version G or later is required to control Astro-Physics compatible telescopes. Note that if you own an older model AP controller that uses an earlier firmware version, TheSkyX Serious Astronomer Edition will still control it; however, newer firmware features will not be available.
Software Bisque strongly recommends using the latest available firmware for your telescope. Contact Astro-Physics for details about upgrading your mount's firmware.
|
|
|
Advanced Series |
All models, including:
|
|
|
CGEM Series |
All models, including:
|
|
|
CGE Series |
All models, including:
|
|
|
CPC Series |
All models, including:
|
|
|
GT Series |
All models, including:
|
|
|
NexStar GPS |
All models, including
|
|
|
i Series
|
All models, including:
|
|
|
NexStar (non-GPS)
|
All models, including:
|
|
|
SE Series |
All models, including:
|
|
|
SmartStar Az/Alt "Cube" mount with GotoNova Controller |
All models*
*iOptron mounts use the Silicon Labs CP210X USB to UART Bridge computer chip for serial communications on Windows. A Virtual Serial Port Driver must be installed before TheSkyX can communicate with this mount.
|
|
|
German Equatorial Mounts |
All models, including:
|
|
|
NGC Sky Vector and Sky Commander |
All models
|
|
|
MI Series Mounts |
All modes, including:
Mathis Instruments mounts use either the Gemini Astronomical Positioning System or the Bisque TCS (TheSkyX Professional Edition only).
|
|
|
LX200™ (classic) |
All models, including:
|
|
|
Autostar |
All models, including:
*Requires Meade Autostar Computer Controller #497 with RS232 serial port.
|
|
|
LX200 GPS Series (Autostar II) |
All models, including:
ACF Models
SCTs
"Ritchey-Chrétian"
|
|
|
MI-250 Equatorial Mounts
|
Mountain Instruments mounts use Gemini Astronomical Positioning System for go to telescope control.
|
|
|
Orion® Telescopes & Binoculars
|
Atlas™ EQ-G Equatorial Mounts
|
This mount uses the same control system (and the same serial communication protocol) as the NexStar GPS and other later model Celestron International "go to" telescopes.
|
|
Sirius™ EQ-G Equatorial Mounts |
This mount uses the same control system (and the same serial communication protocol) as the NexStar GPS and other later model Celestron International "go to" telescopes.
|
|
|
SkyQuest IntelliScope
|
See Tangent Instruments Device Support below |
|
|
|
|
All models |
|
Gemini Astronomical Positioning System* |
All models, including:
*TheSky6 uses the LX200 protocol to communicate with the Gemini APS.
|
|
|
|
Sky Commander
|
All models, including:
|
|
|
SkyWatcher™ Mounts |
All models that use the SynScan Controller, including:
The SkyWatcher mounts use the SynScan control system for go to control; the SynScan control system uses the NexStar 5 communications protocol (which TheSky6 supports).
|
|
BBox |
Tangent Instruments BBox
|
|
|
|
All models
|
|
|
Temma |
All models, including:
|
|
|
Encoder-to-serial boxes |
All models, including:
|
|
|
|
Sky Sensor |
All models
|
|
STAR BOOK Star-Chart Go To System |
TheSkyX Serious Astronomer Edition can control any mount that uses the STAR BOOK Star-Chart Go To System, including (but not limited to) the following models:
If your specific telescope model is not listed, but uses the Vixen STAR BOOK Star-Chart Go To System, TheSkyX SAE can control it.
|
|
|
Argo Navis |
All models
|